Micro-sized thin-film solar cells via area-selective electrochemical deposition for concentrator photovoltaics application.

Micro-concentrator solar cells enable higher power conversion efficiencies and material savings when compared to large-area non-concentrated solar cells. In this study, we use materials-efficient area-selective electrodeposition of the metallic elements, coupled with selenium reactive annealing, to form Cu(In,Ga)Se2 semiconductor absorber layers in patterned microelectrode arrays. This process achieves significant material savings of the low-abundance elements. The resulting copper-poor micro-absorber layers' composition and homogeneity depend on the deposition charge, where higher charge leads to greater inhomogeneity in the Cu/In ratio and to a patchy presence of a CuIn5Se8 OVC phase. Photovoltaic devices show open-circuit voltages of up to 525 mV under a concentration factor of 18 ×, which is larger than other reported Cu(In,Ga)Se2 micro-solar cells fabricated by materials-efficient methods. Furthermore, a single micro-solar cell device, measured under light concentration, displayed a power conversion efficiency of 5% under a concentration factor of 33 ×. These results show the potential of the presented method to assemble micro-concentrator photovoltaic devices, which operate at higher efficiencies while using light concentration.

CuInSe2 quantum dots grown by molecular beam epitaxy on amorphous SiO2 surfaces.

The currently most efficient polycrystalline solar cells are based on the Cu(In,Ga)Se2 compound as a light absorption layer. However, in view of new concepts of nanostructured solar cells, CuInSe2 nanostructures are of high interest. In this work, we report CuInSe2 nanodots grown through a vacuum-compatible co-evaporation growth process on an amorphous surface. The density, mean size, and peak optical emission energy of the nanodots can be controlled by changing the growth temperature. Scanning transmission electron microscopy measurements confirmed the crystallinity of the nanodots as well as chemical composition and structure compatible with tetragonal CuInSe2. Photoluminescence measurements of CdS-passivated nanodots showed that the nanodots are optoelectronically active with a broad emission extending to energies above the CuInSe2 bulk bandgap and in agreement with the distribution of sizes. A blue-shift of the luminescence is observed as the average size of the nanodots gets smaller, evidencing quantum confinement in all samples. By using simple quantum confinement calculations, we correlate the photoluminescence peak emission energy with the average size of the nanodots.

Production of nanometer-size GaAs nanocristals by nanosecond laser ablation in liquid.

This paper reports the formation and characterization of spherical GaAs quantum dots obtained by nanosecond pulsed laser ablation in a liquid (ethanol or methanol). The produced bare GaAs nanoparticles demonstrate rather narrow size distribution which depends on the applied laser power density (from 4.25 to 13.9 J/cm2 in our experiments) and is as low as 2.5 nm for the highest power used. The absolute value of the average diameter also decreases significantly, from 13.7 to 8.7 nm, as the laser power increases in this interval. Due to the narrow nanoparticle size dispersion achieved at the highest laser powers two absorption band edges are clearly distinguishable at about 1.72 and 3.15 eV which are ascribed to E0 and E1 effective optical transitions, respectively. A comparison of the energies with those known for bulk GaAs allows one to conclude that an average diameter of the investigated GaAs nanoparticles is close to 10 nm, i.e., they are quantum dots. High resolution transmission electron microscopy (HRTEM) images show that the bare GaAs nanoparticles are nanocrystalline, but many of them exhibit single/multiple twin boundary defects or even polycrystallinity. The formation of the GaAs crystalline core capped with a SiO2 shell was demonstrated by HRTEM and energy dispersive X-ray (EDX) spectroscopy. Effective band edges can be better distinguished in SiO2 capped nanoparticles than in bare ones, In both cases the band edges are correlated with size quantum confinement effect.

Switchable bactericidal effects from novel silica-coated silver nanoparticles mediated by light irradiation.

Here we report on the triggering of antibacterial activity by a new type of silver nanoparticle coated with porous silica, Ag@silica, irradiated at their surface plasmon resonant frequency. The nanoparticles are able to bind readily to the surface of bacterial cells, although this does not affect bacterial growth since the silica shell largely attenuates the intrinsic toxicity of silver. However, upon simultaneous exposure to light corresponding to the absorption band of the nanoparticles, bacterial death is enhanced selectively on the irradiated zone. Because of the low power density used for the treatments, we discard thermal effects as the cause of cell killing. Instead, we propose that the increase in toxicity is due to the enhanced electromagnetic field in the proximity of the nanoparticles, which indirectly, most likely through induced photochemical reactions, is able to cause cell death.

Laser-ablation-induced synthesis of SiO2-capped noble metal nanoparticles in a single step.

Here we describe a simple, powerful technique based on the laser ablation of a target immersed in a water solution of a metal salt. With this method, nanoparticles of different metals and alloys can be processed very quickly. Both the target and the salt solution can be chosen to produce metal nanoparticles of different sizes, surface-oxidized nanoparticles (silica-silver, for example), or even more complex structures to be defined by the researcher on one or more steps because the technique combines the advantages of both physical and chemical methods. We have applied this technique to the fabrication of inert silica-metal (silver, gold, and silver-gold) nanoparticles with a strong surface plasmon resonance all together in a single step. The advantage of the simultaneous production of silica during laser ablation is the stabilization of the metal nanoparticle colloid but also the possibility to reduce the toxicity of these nanoparticles.